Install the control box is installed a explosion-proof electric hoist must check. The control box comprises a box body, a contactor, a transformer, terminals and other components, from the hinge can be disassembled, is convenient for the users to install, repair.
In general, the control box explosion-proof electric hoist installation mainly pay attention to the following points.
1.Before installation must check whether the loosening of screw connections, whether the product is damaged, in the transport process defects found, risks must be removed quickly.
2.The control box must be installed vertically, the tilt angle less than 5 degrees.
3.The test must check the working status of hoist explosion-proof electric with key agreement, if not should adjust the control box, change the phase sequence.
4.The installation should pay attention to the connection code, should be in accordance with the electrical schematic wiring.

1.The ambient air temperature is -20 ℃ ~ +40 ℃.
2.The relative humidity in the air: the lowest average humidity is 90%, and the average minimum monthly temperature is 25 ℃, and taking into account due to temperature changes on the surface of the product of the frost.
3.The work field must be no place severe shaking and vibration.
4.In no danger of explosion in the medium, and medium without corrosion and damage to the insulator of gas and dust (including conductive dust).
5.Not more than 2500 meters of altitude.
6.In the absence of snow or rain (rain local control box except).

Explosion-proof electric hoist control box is composed of box body, transformer, contactor, a connector and so on..explosion-proof electric hoist control box with organic chain quality AC contactor, the load and the instantaneous overload ability are greatly improved, better reliability, more suitable for lifting appliances frequent operation, protection shell is made of high quality cold rolling plate stretch forming, electrostatic spray etc..
Explosion-proof electric hoist control box can also provide different lengths of cable and flashlight door according to user requirements, the cover of control box is opened, the hinge can be disassembled, is convenient for the users to install, repair, control box can take the electrical appliances chain and mechanical linkage, so that two contactor group cannot be connected to the circuit; each control box is provided with electrical schematics, wiring terminal with schematic consistent clear number, easy to repair, terminal user.

Double rail electric hoist novel and compact structure, superior performance, panic is small in size, loading weight easily, speed stability, and more safety.
1.Clearance of small size, full and effective use of space workshop
Double rail electric hoist "C" size is small, compared to similar products, lifting height is higher, and the two sides limit distance smaller hook to metope, can effectively increase the work area.
2.Stable operation, fast positioning
The use of variable frequency drive users to lift or operation process can accurately locate the load, reducing swing lifting objects, increase safe operation in the process of safety and comfort.
3.Excellent performance
The double rail electric hoist can greatly improve the performance and productivity of equipment, but also increase the safety.
The reliability and safety of 4 super
High performance is connected to a motor cooling performance duration rate than similar products improves the brake safety service life of high performance over a million times. Brake for automatic wear adjustment, prolong the service life of the gourd.
5.Large diameter roller, prolongs the service life, reduce the deflection angle
Design of large diameter roller double rail electric hoist greatly extend the life of the wire rope, improve safety at work. At the same time, large diameter drum hoist has reduced the angle, achieve the vertical lifting hook, accurate positioning, small drift, use more convenient.
6.Humanized design
Double rail electric hoist from the performance and use of full consideration to the needs of customers, enabling customers to increase safety and comfort in the use process. Security, a limit switch device to improve the operating process; ergonomic design makes the operator easy grip, convenient lifting goods.

Explosion-proof electric hoist, compact structure, safe and reliable, high transmission efficiency, lighter weight. Square four are reserved with mounting holes, easy to install, can meet the requirements of different working conditions. The reducer adopts a totally enclosed type planetary reducer, high precision, long service life, low noise, maintenance free, the factory that has been debugged and good gear oil, without debugging.
High quality lifting drive to ensure smooth and efficient operation of security, to ensure that the structure is compact in design of offset the size of the smallest hook, lifting with double speed (frequency optional), car are standard conversion, to ensure efficient operation, lifting equipment of workshop logistics efficiency, to ensure that the work plan of customer on schedule execution.
There are many kinds of protection function, to ensure the safe and reliable device for crane operation, the operation monitoring unit can explosion-proof electric hoist operation, motor running state and safe working cycle calculation were recorded in detail, and provide a warning. All records can provide data for repair, understand the root of the problem, let the crane maintenance plan more timely and reasonable.
Design of modular design philosophy has always been throughout the entire product, ensure the standard parts and interchangeability, greatly improve the product quality and reduce the maintenance costs of the product. Our company products all have a complete spare parts inventory, the company has a professional service team, to ensure that customers provide after sale service, customers buy equipment after any menace from the "rear".

Electric wire rope hoist pulley is an important component of the electric hoist, wear to a certain standard will be discarded, otherwise it will damage the wire rope and a great hidden danger to safe production.
1, crack, it should not be used again.
2, the rope groove of uneven wear of 3ram.
3, the rope groove wall thickness wear up to 20% of the original wall thickness.
4, because of wear the bottom rope groove diameter reduction to 50% of the diameter of the steel wire rope.
5, Defect of wire ropeother damage.

CD1 electric hoist uses the safety notes summary:
1.CD1 electric hoist check before use of work.
(1) there should be no obstacle in the range and heavy route in the operator walking.
(2) a hand control button on the left and right direction of action should be accurate, sensitive, motor and reducer should be no abnormal noise.
(3) the brake should be reliable and sensitive.
(4) the CD1 electric hoist orbit should be no foreign body.
(5)the upper and lower limit action should be accurate.
(6)hook stop nut should be tightened.
(7)the hook to rotate in the horizontal and vertical direction should be flexible.
(8)the hook pulley should be flexible rotation.
(9)the wire rope should be no obvious defects, on the drum arranged neatly, without off the pulley groove signs, good lubrication.
(10)hanging. No abnormal phenomenon.
Work environment temperature of
(11) CD1 electric hoist for the last 25 ~ +40 ℃
(12)The CD1 electric hoist does not apply to full of corrosive gas or relative humidity above 85% places, cannot replace the explosion-proof gourd, not lifting the molten metal or toxic, flammable and explosive articles.
2.CD1 electric hoist may not be side unloading crane weight, prohibit the use of overload.
3. In the use process, the operator should always check whether there is chaos, wire rope buckle knot, drop groove, wear phenomenon, if there should be excluded, and should always check the rope guide and limit switches are safe and reliable.
4. In the daily work shall not be artificially limiting device to stop the use of heavy lifting or stop the operation of equipment.
5.After work, turn off the power switch, cut off the main power supply.
6.We should set up specialized repair maintenance personnel on a weekly CD1 electric hoist main performance and safety inspection, found fault and remove.
The brake ring seven, motor fan of the brake wheel, not stained with grease, adjusting nut should be tightened, so as to avoid the brake failure and accident.
8.CD1 electric hoist each lubricating part should be the amount of the lubricating oil and lubricating oil in a timely manner, to clean, do not contain other impurities. Lubricating oil for about 2 months to replace a. To hoist reducer and reducer before use must add enough oil, lifting gear into the No. 50 mechanical oil device (HJ-50GB443-64). 0.5T, 1t, 2T, 3T, 5T, 10tCD1 electric hoist LKG 1.5kg, respectively, 2.5kg, 3kg, 3kg, 4kg, running into the viscosity reducer for 5.5 ~ 7º E50. number for lubricating oil 0.3kg.
9.The use of the process, find the fault should be cut off the main power supply in time.
10.The CD1 electric hoist does not work, do not allow the weight hanging in the air, to prevent the parts from the permanent deformation.
11.The CD1 electric hoist after use, should be kept in a safe place specified. Outdoor should fortify the rain cover.
12.,No press the two button of the opposite direction, the other can be operated at the same time.
13.The maintenance lifting reducer disassembly when not using a screwdriver, flat shovel, a joint surface, using wooden hammer tap the protruding part of the box body and the box cover, so as not to damage the sealing surface.

1.The main isolation switch
Electric wire rope hoist with the main isolation switch into the line, switch off the main switch crane without electricity, in order to ensure the safety of maintenance personnel. Small single girder crane ground operation (low headroom electric hoist crane) not to set the main isolation switch.

2.The emergency switch
Emergency switch should be installed within reach and position in the driver, (some point magnetic crane switch and the emergency switch with a type of control electromagnetic disc, when the electromagnetic disc control switch can not and emergency switch installed side by side) to prepare for an emergency, immediately disconnect the power, ensure the safety of personnel and equipment.

3.Short circuit protection
Commonly used short circuit protection device with automatic air switch, fuse, two. Should be set up in the power supply circuit, short circuit protection to do total power circuit.

4,Zero protection
In order to prevent the controller failed to institutions in the zero position, the vehicle suddenly start the accident send electric crane driver, the controller is provided with a zero protection.

5.The loss of excitation protection
No current in his shock excitation winding DC motor's armature current will increase, resulting in failure. And as the crane hoisting mechanism with eddy current speed regulation, the eddy current brake magnetic loss leads to load descending overspeed phenomenon. In the two place, should set the excitation loss protection.

6.Over current protection
Over current relay on the armature circuit in AC motor stator loop, DC motor. When the current exceeds the allowable value, the relay action of the motor power, the motor protection.

7.Interlock protection
The door, the access door to crane cab on the hatch door, ascending or escalator mouth, travel switch, the switch is opened, automatically cut off the power supply, the crane can not start, to protect the safety of personnel.

8.Grounding protection
For preventing crane metal structure is charged by electric shock injury, setting the ground protection.
Ground connection to use a section of not less than 150mm2 or 10mm2 flat copper wire, connected by welding. Is strictly prohibited for current zero line grounding wire. By the rectifier power supply AC power lifting electromagnet, electric should be reliable connection between the shell and the crane. Suspension type control button (electric hoist crane hand switch) should also be reliable electrical connection between the metal shell and the crane. Crane and rail office ground resistance point shall not be less than 4.

The CD1 electric hoist motor protector has the mechanical development of the past for electronic and intelligent, can directly display the parameters of motor current, voltage, temperature, sensitivity, high reliability, multiple functions, convenient debugging, protection fault type of stick out a mile, which reduces the motor is damaged, and greatly facilitate the fault judgment, is conducive to the production site of fault processing and shorten the recovery time of production.

Due to the continuous development of insulation technology, not only to increase the output of the motor design, and reduce the volume, heat capacity of the new CD1 electric hoist motor is more and more small, load capacity is more and more weak; due to the improvement of production automation, the motor always runs in frequent starting, braking, reverse and variable load and so on many kinds of ways, put forward higher request to the motor protection device.

CD1 electric hoist motor protection device of traditional dominated by thermal relay thermal relay, but low sensitivity, large error, poor stability, protection is not reliable. Indeed, although many of the equipment installed in the thermal relay, but motor damage and affect the normal production of the phenomenon is still exist.

The ideal CD1 electric hoist motor protector is not the most functional, not the so-called advanced, but should meet the actual needs, to achieve unity of economy and reliability, high ratio of performance to price. Reasonable selection of protection device type, function according to the actual situation, considering the protector installation, adjustment, simple and convenient to use, it is more important to choose the protector of high quality.

1.Electric wire rope hoist is used for steel wire rope to lift goods, in order to avoid rope quit, but also the guide rope is installed, so as not to cause unnecessary trouble. According to the international standard of wire rope as 5 root burr, for the sake of safety, you should replace the wire rope in time. These measures effectively increases the service life of the electric hoist.

2.Electric wire rope hoist dual brake system is safe and reliable. But electric wire rope hoist hang oneself have a limit switch, prevent beyond limit.

3.Electric wire rope hoist special reverse phase relay protection devices, power supply wiring error, control circuit, unable to move. Electric wire rope hoist in case of power failure, the automatic brake, brake immediately and automatically.

4.Electric wire rope hoist voltage 24V/48V conversion, prevent leakage, possible accidents, ensure the safety of the use of rain.

5.Electric wire rope hoist with other core light socket, unlike other gourd is: electric wire rope hoist with a safety hook of the lock hook pad 360 degree universal connectivity.

6.Wire rope with built-in safety facilities, easy control of lifting, for warehouse, housing area, the workplace and light industry manufacturing.